HARMAN KARDON AVR35
Service Manual

Remote Control

is being used to control a TV, VCR or Cable box.,press these button to change the channel being viewed.

NOTE : Pressing one of these buttons selects the source only. In order to control the actual source machine using the remote you must press the Press Control Selector button for

frequency up or down in single-step increments. When the FM band is in use, pressing this button when a station's signal is weak will change to monaural reception, as indicated by the MONO indicator .

of the input sources connected to the AVR-35. After pressing this button, use the / buttons to make your selection between OPTICAL or COAXIAL digital. Press the Set button

Surround Mode Selector : Press this button to begin the process of changing the surround mode. After the button has been pressed, use the / button to select the

the desired product.

to enter your choice.

+10 Button : This button does not have a function for the AVR35, but when the remote is used to control certain CD players, TV sets and VCRs it may be used to select tracks or channel numbers.

Direct/Enter : Press this button to select a radio station by entering its frequency using the Numeric Key 14 . Enter : This button does not function with the AVR35, but it is available for use with other

Speaker Configuration : Press this button to begin the process of configuring the AVR-35's Bass Management System for use with the type of speaker used in your system. Once the button has been pressed, use the buttons
to select the channel you wish to

desired surround mode. / Buttons : These are multi-purpose

/

buttons. They will be used most frequently to select a surround mode. To change the surround mode, first press the SURR button . Next Numeric Keys : These buttons serve as a ten-button numeric key-pad to enter tuner preset positions. They are also to be used to select channel numbers when TV has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

devices.

set up. Press the Set button 10 , and then select another channel to configure. When all

press these buttons to scroll up or down through the list of surround modes that appear in the Information Display . These buttons are also

Preset Up/Down : When the tuner is in use, these buttons scroll through the stations that have been programmed into the AVR-35's memory, When many source devices, such as CD players, VCRs and cassette decks, are selected using the Device Control Selectors

adjustments have been completed, press the Set button twice to exit the settings and return to normal operation.

used to increase or decrease output levels used to lower the AVT35's output levels when configuring the unit with either the intermal test tone or an external source. They are also used to enter delay time settings after the Delay button 24 has been pressed.

Mute : Press this button to momentarily silence the AVR35 or TV set being controlled, depending on which device has been selected.

NOTE : The 0 button has a dual function. It also serves as the CLEAR button for use in programming the tuner or clearing the system memory.

. these buttons will normally function as chapter step or track advance.

When the AVR35 remote is being programmed Tuning Up/Down : When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode button
has been pressed so that the

to operate another device, this button is pressed with the Device Control Selector button to begin the programming process.

/

Channel Button : This button is used Info Button : This button dose not function with the AVR-35, but it is available for use with other devices.

to start the process of setting the AVR-35's output levels to an external source. Once this button is pressed, use the / buttons 8 to

AUTO indicator

is illuminated, pressing these

Volume : Press these buttons to raise or lower the system volume.

select the channel being adjusted, then press the Set button , followed by the / buttons Clear Button : This button dose not function with the AVR-65, but it is available for use with other devices. Set Button : This button is used to enter settings into the AVR-35's memory. It is also used in the setup procedures for delay time, Program/Command Indicator : This LED is used as an indicator to assist in programming the AVR-35. Note that the button will briefly turn red after it has been pressed to confirm your selection. Sleep Button : Press this button to place AVR Selector : Press this button to use the remote control for operation of the AVR-65. Note that the button will briefly turn red after it has been pressed to confirm your selection. the unit in the Sleep Mode. After the time shown in the display, the AVR-35 will automatically go into the standby mode. Each press of the button changes the time until turn-off in the following order: Device Control Selectors : Press one of these button to use the remote to control the functions of another audio/video device. Note that the button will briefly turn red after it has 90 min 30 min Channel 80 min 20 min 70 60 50 40 min min min min 10 5 1 OFF min min min min Buttons : When the remote Power Button : Press this button to turn the currently selected device on or off. been pressed to confirm your selection. speaker configuration and channel output level adjustment. Memory Button : Press this button to enter a radio station into the AVR-35's preset memory. After pressing the button the MEMORY indicator will flash, and you then have five seconds to enter a present memory location using the Night Mode : Press this button to activate the "Night" mode, preventing loud playback when the digital modes are in use without altering the dynamic range of the output signal. NOTE : Although the word "Sleep" appears above this button, it refers to control of devices other than the AVR-35. Use the Sleep button When the AVR-35 remote is being programmed to operate other devices, this button is pressed to begin a readout of a programmed code. Source Selectors : Press these buttons to select an input source for the AVR-35. The AM/ FM button is also used to switch between frequency bands when the tuner in use. Tuner Mode : Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so that the AUTO indicator pressing the Tuning buttons goes out, to control the AVR-35's Sleep function. Numeric Keys .

buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the AUTO indicator is NOT

again to change the level setting.

Test : Press this button to begin the sequence used to calibrate the AVR-35's output levels. TV/VCR : This button does not function

illuminated, pressing these buttons will tune stations in single-step increments.

Transport Control : These controls do not control any function of the AVR-35, but they are used extensively when operating a wide variety of CD players, cassette decks and VCRs. Delay/Prev Ch. : Press this button to begin the process for setting the delay times used by the AVR-35 when processing surround sound. After pressing this button the delay times are entered by pressing the Set button then using / buttons
, and to change the

with the AVR35, but it is available for use with
other devices.

setting. Press the Set button again to complete the process. / Digital Button : This button is used to

will move the

select the type of digital input used with any one

7